Personal Target ID Chart Builder
Log your own detector's Target ID readings on known items and get a min–max chart that is true for your machine. No preset numbers.
- Free
- No sign-up
- Runs in your browser
Estimates only · data checked November 2026 · About this data
Your chart reflects only your own readings and is valid only for the detector, settings and items you tested. A Target ID number never identifies a target with certainty.
Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.
Quick answer
A personal target ID chart builder turns the numbers your detector shows on your test items into a chart that is true for your machine. Log several readings per item and the tool shows the lowest-to-highest range and the count for each item. It uses no preset numbers, and nothing is uploaded.
How to use the personal target ID chart builder
- Enter your detector model. Type it the way you like. Spacing and capital letters don’t matter, so “Equinox 800” and “equinox 800” end up in the same chart.
- Test a known item and log the number. Air-test it by passing it over the coil, or ground-test it by burying it in your test garden. Pick the item type (coin, ring, foil, pull-tab or other), type exactly what your display shows, and press Add reading. Decimals and negative numbers are accepted.
- Repeat several times per item. One reading is not a range. Change the number to the next reading you see and press Add reading again. Duplicate numbers are allowed and counted.
- Print or export the chart. Each item shows the min–max of your own readings and how many readings it is based on.
Under the chart, each item can be expanded to show every individual reading with its own Delete button. If one swing was obviously wrong, for example the coil hit a nail, delete that entry yourself. If you test more than one detector, a selector lets you switch between their charts. Clear all asks for confirmation before it removes anything. Reset starts a new chart: it clears the form and removes all readings, so export JSON first if you want to keep them.
How the chart is calculated
The method is deliberately simple and transparent. The tool filters your readings to the selected detector and groups them by item. Each “other” item gets its own group under the exact name you typed (only spacing and capital letters are ignored), so “No.5 tab” and “No 5 tab” stay separate. For every group it reports three things: the smallest number you logged (min), the largest (max), and the number of readings (n). If min and max are the same, it shows that single value together with n.
| What you log for one item | What the chart shows |
|---|---|
| One reading | That value, with n = 1 and a hint to log more |
| Several readings, all the same number | That single value, with n = the count |
| Several readings that vary | Lowest–highest, with n = the count |
| Readings from another detector | Nothing. They appear only on that detector’s chart |
The tool never averages, smooths or drops outliers on its own. A range that shows the full spread of your own readings is more honest than one tidy number, because Target IDs move with depth, coil angle, ground conditions and the item itself.
Why a universal metal detector ID chart misleads (and what to do about Equinox chart numbers)
Searches for a “metal detector id chart” or a “metal detector number chart” usually lead to one table that claims to map numbers to metals for every machine. No such universal mapping exists. Each manufacturer defines its own Target ID scale, and scales differ even within one maker’s lineup. Minelab’s published specifications give the EQUINOX 900 and the VANQUISH 540 different non-ferrous ranges. The MANTICORE uses a two-dimensional ID display with its own scale. The same coin can therefore show one number on one detector and a different number on another.
Settings, coil and ground also move the number on a single detector. That is why this page prints no chart of typical coin, ring, foil or pull-tab numbers. If you are looking for Equinox metal detector chart numbers, the reliable answer is to build them. Enter your Equinox model, test the coins, rings and trash you actually find, and log what your screen shows. The result is valid for that detector, and only that one. Even then, a number suggests what a target might be; it never identifies it with certainty.
How to log good readings
- Log several readings per item, not just one.
- Keep test conditions the same: same settings, same coil, same height and same spot.
- Use items you know, ideally ones like the targets you hunt for.
- If you change settings or the coil, consider logging under a new detector name, such as “Equinox 800 – Park mode”, so the charts stay separate.
Print or save your chart
Your readings are kept in this browser tab only. Nothing is saved to the device or uploaded, so the readings disappear when you reload or close the page, or press Reset. Before you leave, choose one of these:
- Print chart prints only the detector name, your chart table, the printed date and the note “Personal readings, valid for this detector only.” The form and buttons are left out. The button is disabled until there is something to print.
- Export CSV downloads a spreadsheet of every reading.
- Export JSON downloads a file you can import later to continue building your chart.
Methodology & sources
All numbers come from your own readings. This page uses no third-party number tables. The chart groups readings per detector (matched after trimming spaces and ignoring capital letters) and per item. It shows min–max and n, with no averaging and no preset or sample data. The accepted input range is a technical sanity limit only and does not describe any detector’s scale. The Minelab pages below are cited only to show that published scales differ between models.
- Minelab EQUINOX 900 tech specs: published Target ID scale (accessed November 2026)
- Minelab VANQUISH 540 tech specs: published Target ID scale (accessed November 2026)
- Minelab MANTICORE tech specs: published 2D ID scale (accessed November 2026)
Last updated: November 2026
FAQ
Why do Target ID numbers differ by detector?
Each manufacturer and model uses its own Target ID scale and processing. The same coin can show different numbers on two detectors, so a chart is only true for the machine it was built on.
Can I use this for any detector model?
Yes. The tool assumes no scale. You type the model name and the numbers your own display shows, and the chart uses only those readings.
Is my data uploaded or saved?
No. Readings stay in this browser tab and nothing is sent anywhere. Export CSV or JSON, or print, before you close or reload the page, and import the JSON file later to continue.
Why does the chart show a range instead of an average?
Readings move with depth, angle, ground and the item itself. The lowest-to-highest range of your own readings shows that spread honestly. The tool never averages or drops readings; you delete bad ones yourself.
Can I build an Equinox metal detector chart with numbers?
Yes. Enter your Equinox model, air-test your own items, and log what the screen shows. You get a chart for your detector, settings and items instead of a copied table.
Related guides
More free tools
Beach & Water Hunt Waterproof Depth Checker
Compare your metal detector's stated waterproof rating with your planned beach or water hunt, checking detector, coil and headphones.
Digging Tool Selector by Ground Type
Pick your ground, hunt type and carry preference to see which digging tool types (shovel, trowel, hori hori, Lesche, scoop) fit best.
Gold Weight and Value Calculator
Convert gold between grains, grams, pennyweight and troy ounces, apply karat or fineness, and estimate value from a spot price you enter.
